Ford Ecosport: Electronic Feature Group
Ford Ecosport 2014-2026 Service and Repair Manual / Electronic Feature Group
- Perimeter Anti-Theft Alarm
- Description and Operation - Perimeter Anti-Theft Alarm - Component Location
- Description and Operation - Perimeter Anti-Theft Alarm - Overview
- Description and Operation - Perimeter Anti-Theft Alarm - System Operation and Component Description
- Diagnosis and Testing - Perimeter Anti-Theft Alarm
- Removal and Installation - Intrusion Sensor
- Passive Anti-Theft System (PATS) - Vehicles With: Keyless Entry and Push Button Start
- Description and Operation - Passive Anti-Theft System (PATS) - Component Location
- Description and Operation - Passive Anti-Theft System (PATS) - Overview
- Description and Operation - Passive Anti-Theft System (PATS) - System Operation and Component Description
- Diagnosis and Testing - Passive Anti-Theft System (PATS)
- General Procedures - Anti-Theft Key Programming - Scan Tool
- General Procedures - Key Programming Using Two Programmed Keys
- Removal and Installation - Passive Anti-Theft System (PATS) Center Antenna
- Removal and Installation - Passive Anti-Theft System (PATS) Front Antenna
- Cruise Control
- Description and Operation - Cruise Control - Overview
- Description and Operation - Cruise Control - System Operation and Component Description
- Diagnosis and Testing - Cruise Control
- Side and Rear Vision
- Description and Operation - Blind Spot Information System - Component Location
- Description and Operation - Blind Spot Information System - Overview
- Description and Operation - Blind Spot Information System - System Operation and Component Description
- Diagnosis and Testing - Blind Spot Information System
- Removal and Installation - Side Obstacle Detection Control Module (SODCM)
- Multifunction Electronic Modules
- Description and Operation - Module Controlled Functions - Overview
- Description and Operation - Module Controlled Functions - Component Location
- Description and Operation - Module Controlled Functions - System Operation and Component Description
- Diagnosis and Testing - Body Control Module (BCM)
- General Procedures - Factory Mode Deactivation
- General Procedures - Transport Mode Deactivation
- Removal and Installation - Body Control Module (BCM)
- Removal and Installation - Driver Door Module (DDM)
- Removal and Installation - Passenger Door Module (PDM)
- Removal and Installation - Rear Door Module (RDM)
General Procedures - Module Programming
Check
NOTE:
Perform the following pre-checks to make sure module programming completes without errors.
Start the programming session in KOEO ...
Other information:
Ford Ecosport 2014-2026 Service and Repair Manual: General Procedures - Refrigerant System Tests - 2.0L Duratec-HE (129kW/175PS)
Inspection NOTE: Procedure 1 — Ambient Temperature between 21°C (70°F) and 38°C (100°F) NOTE: Variable compressors may not stroke up unless the ambient temperatures are above 21°C (70°F) when conducting the pressure mapping procedure. Variable compressor need to see a thermal load on the system in order to create normal operating pressures. Run the engine ..
Ford Ecosport 2014-2026 Service and Repair Manual: Description and Operation - Safety Precautions - Overview
Overview Before beginning any service procedure in this manual, refer to health and safety warnings in section 100-00 General Information. Failure to follow this instruction may result in serious personal injury. WARNING: Before servicing any tire, ask the customer if anyone injected a tire sealant into the tire. Tire sealants may be flammable and can burn or explode ..
Categories
- Manuals Home
- 2nd Gen Ford Ecosport Service Manual (2014 - 2026)
- Removal and Installation - Roof Rail
- Removal and Installation - Fuel Pump and Sender Unit
- Description and Operation - Evaporative Emissions - System Operation and Component Description
- Diagnosis and Testing - Body Control Module (BCM)
- Removal and Installation - Transmission
Removal and Installation - Variable Camshaft Timing (VCT) Unit
Removal
NOTICE: During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan can cause engine failure.
Remove the timing chain.Refer to: Timing Chain (303-01C Engine - 2.0L Duratec-HE (129kW/175PS), Removal and Installation).
Remove the bolts and VCT units.
Discard the bolts.
Copyright © 2026 www.foecosport2.com